If your iPhone is iPhone 8, iPhone 8 plus or iPhone X, select Allow untested iOS/iPadOS/tvOS versions and Skip All BPR check. After we enter the Checkra1n interface, choose Options. Press Alt + F2, to run the Checkra1n jailbreak tool. Press F12 before the brand logo appears, then choose your flash disk. Close the app, and restart your computer. Open BalenaEtcher, click Flash from file, and select the downloaded image. Download BalenaEtcher and Checkn1x iso file. You’d better make a backup for your USB drive data in case of data loss. Insert your USB flash drive to the computer. A USB flash drive (at least 2GB capacity).Ī Step-by-Step Guide to Jailbreak your iOS Device on Windows with Checkn1x Part 1# Burn the USB Flash Drive What Do You Need for Jailbreaking Your Device on Windows?Ģ. Watch the video to jailbreak iOS Device with Checkn1x: Therefore, you can use Checkn1x to jailbreak iOS device. Jailbreak iOS Device on Windows with Checkn1xĬheckn1x is a Linux-based ISO distribution preinstalled with Checkra1n. If you are still unable to jailbreak, please try the following steps again. Now that your device has been jailbroken, you can use it as you wish. The process will take some time to complete. iRa1n will start jailbreaking automatically. Put your device into DFU mode by following the instructions onscreen. Next, click Start to jailbreak your device. On iOS 14.3 and earlier, you can jailbreak your device directly. For jailbreak Apple 8-X (iOS 14.0~14.3+): you should click "Options" and choose "Skip A11 BPR check", then go back to jailbreak.Ĥ. For Apple 8-X (iOS14.4 and above): you should choose "Options" and check "Allow untested iOS/iPadOS/tvOS versions" and "Skip A11 BPR check".ģ. ![]() ![]() For Apple 6s-7P and iPad series (iOS14.4 and above): You should select "Options" and choose "Allow untested iOS/iPadOS/tvOS versions", then return to jailbreak.Ģ. If you have a screen connected to the Generic x86-64 system, after a minute or so the Home Assistant welcome banner will appear in the console.1. Plug in an Ethernet cable that is connected to the network.Ubuntu), shut it down and remove the live operating system USB device. If you used a live operating system (e.g. If you used your desktop system to write the HAOS image directly to a boot medium like an S-ATA SSD, connect this back to your Generic x86-64 system. When Balena Etcher has finished writing the image you will see a confirmation.Click on “Flash!” to start writing the image.Select the boot medium (storage device) you want to use for your installation. ![]() When Balena Etcher has downloaded the image, click “Select target”.Paste the URL for the Generic x86-64 image into Balena Etcher and click “OK”. ![]() Select and copy the URL or use the “copy” button that appear when you hover it. Next, we need to write the Home Assistant Operating System image to the “boot medium”, which is the medium your x86-64 hardware will boot from when it is running Home Assistant. To enter the BIOS, start up your x86-64 hardware and repeatedly press the F2 key (on some systems this might be Del, F1 or F10). However, the options should still be present and named similarly. The BIOS menu will likely look different on your system. The following screenshots are from a 7th generation Intel NUC system. To boot Home Assistant OS, the BIOS needs to have UEFI boot mode enabled and Secure Boot disabled. Configure the BIOS on your x86-64 hardware There are two ways to do this listed below. You will need to configure your Generic x86-64 PC to use UEFI boot mode, then write the HAOS (Home Assistant OS) disk image to your boot medium. Pretty much all systems produced in the last 10 years support the UEFI boot mode. The system must be 64-bit capable and able to boot using UEFI. This guide assumes that you have a dedicated Generic x86-64 PC (typically an Intel or AMD-based system) available to exclusively run Home Assistant Operating System.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |